How to Replace a Tub
How to Replace a Tub
Blog Article
The author is making a number of good annotation on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in the content following next.
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the project can move speedily; if you have to open a wall to remove the old tub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This article will help you mount a brand-new bath tub in your washroom if you have actually currently gotten a brand-new tub as well as don't need to change the arrangement of your previous water supply pipelines.
Your devices as well as product checklist ought to comprise the following:
Planning for the Installment
First of all, the supporting frame provided with the bath should be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and also examine all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub must wait up until the tub has been utilized at least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with dampness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog posting on How to Install a Bathtub while doing a lookup on the search engines. Are you aware of another individual who is truly interested in the topic? Feel free to promote it. I recognize the value of reading our article about How to Install a Bathtub.
Book Appointment Report this page